- PROSCAN TABLET PLT7777G Q STUCK ON ANDROID SCREEN INSTALL
- PROSCAN TABLET PLT7777G Q STUCK ON ANDROID SCREEN ANDROID
- PROSCAN TABLET PLT7777G Q STUCK ON ANDROID SCREEN PASSWORD
PROSCAN TABLET PLT7777G Q STUCK ON ANDROID SCREEN ANDROID
You will see an image of an Android robot with a red exclamation mark.
You will see the word Start with an arrow drawn around it.
PROSCAN TABLET PLT7777G Q STUCK ON ANDROID SCREEN PASSWORD
If your tablet is password protected, you'll be prompted to enter your Pattern, PIN, or Password.
PROSCAN TABLET PLT7777G Q STUCK ON ANDROID SCREEN INSTALL
Go through the new install process, adding your account/s & wifi details. The system should then Factory Reset as in the "settings" process (method 1). Press the VOL DOWN button to select the "Wipe Data" icon then VOL UP to confirm it.ĥ. In JB there are four, the first of which is RCK.Ĥ. The right "Android" will have a green highlight fading in and out. After a few seconds you should see some icons in the middle of the screen - in ICS they are called "Wipe Data" and "Android". If the TF booted the way it always does, you have not accomplished the task, try again until you have seen 2 icons (ICS), 4 icons (JB) in the screen.ģ. Press and hold the VOL DOWN and then POWER button at the same time for at least 10-12 seconds until after the start-up screen appears and is joined by some small print at the top of the screen, then let them both go. Unplug the power cord and shut the unit off.Ģ. If you are unable to power off, try this process from point 2.ġ. Couldn't hurt, worth a try to avoid losing your stuff.ĪSUS Transformer (most models are reset the same way) Most say to hold the Power button in for about 20 seconds or until the power menu appears (Power Off if you get the menu.), Then wait about a minute before powering on again. Just in case.)Įdit: I've come across many recommendations to try a "Soft" reset, before resorting to a "Hard" reset such as the ones in this thread. (If your tablet has a MSD card, I'd recommend removing it as well. Note: Anyone using one of the procedures below should be aware that ALL personal data will be deleted from the tablet as part of the process. Any questions posted here may be deleted without notice by the Forum Staff. Questions belong in the forum for your tablet or, if there is no forum for your tablet, in the Q&A section. This is a thread for ANSWERS NOT QUESTIONS. You'll also have the appreciation of the Forum Staff. Your "reward" for doing so will be the gratitude of anyone who uses it successfully and hopefully some clicks of the "Thank" thingy in your post. Place the Make & Model of tablet on the first line to make searching easier. If you know of a procedure that works for a particular tablet (that the example in the second post does not work for), please post it in the same format as the second post for consistency. Hopefully, this will be a community effort and you'll participate if you can. Please remember to backup any important data before performing a Hard Reset.This thread is intended to gather the many "Factory Reset" replies scattered all over the forums into one location. If you perform a Hard Reset, all user applications, user data and DRM licenses will be deleted.
Move the bar again using the reset button and highlight Yes - delete all data and press the POWER button. Press the POWER key to get in the next menu.Ħ. To highlight the options use the paper clip and press the RESET button to move down the highlighter bar until you get to Wipe data / Factory Reset. Keep pushing the two buttons until the recovery menu displayed.ĥ. To get into the Android recovery menu you have to click it push it down again the tiny little RESET button in the hole and the POWER button together. Release the Power and the reset button.Ĥ. (Note this is not the RESET hole on the back of the device.)ģ. While you are pressing the reset button press and hold the Power button also until the Proscan logo comes up and the Android robot is displaying on the screen. Find the tiniest RESET hole on the side of the tablet next to the micro USB charger port and use a paper clip or similar tool to click it, press gently the RESET button in the hole.